超聲波清洗機換能器怎么用？核心是頻率匹配+場景適配

　　How to use the transducer of ultrasonic cleaning machine? The core is frequency matching+scene adaptation

　　在超聲波清洗機的運行系統中，清洗換能器是把電能轉換成超聲振動的核心部件，相當于清洗機的“動力心臟”。不少用戶在使用時容易忽視換能器的正確操作，導致清洗效率差、換能器易損壞。其實，不同頻率的清洗換能器，使用關鍵就在于“頻率匹配+場景適配”。今天就專門科普超聲波清洗機不同頻率清洗換能器的正確使用方法，把幾個核心要點講清楚，幫大家避開使用誤區，確保清洗效果和設備壽命。

　　In the operation system of ultrasonic cleaning machine, the cleaning transducer is the core component that converts electrical energy into ultrasonic vibration, equivalent to the "power heart" of the cleaning machine. Many users tend to overlook the correct operation of the transducer during use, resulting in poor cleaning efficiency and easy damage to the transducer. In fact, the key to using different frequency cleaning transducers lies in "frequency matching+scene adaptation". Today, we will specifically explain the correct usage of ultrasonic cleaning machines for cleaning transducers at different frequencies. We will clarify several key points to help everyone avoid misunderstandings and ensure cleaning effectiveness and equipment lifespan.

　　第一要點：先確認頻率對應，這是基礎前提。換能器的標稱頻率必須和超聲波發生器的輸出頻率嚴格一致，絕對不能混用。比如20kHz的換能器要搭配20kHz的發生器，60kHz的換能器就對應60kHz的發生器，高頻段的100kHz換能器也只能適配同頻率發生器。很多人誤以為“頻率相近就行”，其實不然——頻率不匹配會讓換能器無法正常共振，不僅清洗效率驟降，洗不干凈工件，還會導致?lián)Q能器發熱嚴重，長期使用會直接損壞，甚至可能燒毀發生器，造成設備故障。

　　The first point is to confirm the frequency correspondence, which is the basic premise. The nominal frequency of the transducer must be strictly consistent with the output frequency of the ultrasonic generator and must not be mixed. For example, a 20kHz transducer needs to be paired with a 20kHz generator, a 60kHz transducer corresponds to a 60kHz generator, and a high-frequency 100kHz transducer can only be adapted to the same frequency generator. Many people mistakenly believe that "similar frequencies are enough", but in fact, this is not the case - frequency mismatch can prevent the transducer from resonating properly, not only causing a sharp drop in cleaning efficiency and inability to clean the workpiece, but also leading to severe heating of the transducer. Long term use can directly damage it, and even burn out the generator, causing equipment failure.

　　第二要點：按清洗需求選對安裝方式，適配不同頻率特性。不同頻率的換能器，安裝位置和方式有明確講究，要結合其性能特點匹配場景。低頻換能器（20-40kHz）的優勢是沖擊力強，適合處理重油污、大顆粒污漬，安裝時優先選清洗槽底部或側面，這樣能讓超聲振動直接作用于工件表面，最大化剝離頑固污漬；高頻換能器（100kHz以上）主打精密清洗，需要均勻分布在槽體四周，確保超聲能量覆蓋整個清洗區域，尤其是能深入工件的縫隙和微孔，保證清洗無死角，同時避免局部能量過強損傷精密工件。

　　Second point: Choose the correct installation method according to the cleaning requirements and adapt to different frequency characteristics. There are clear requirements for the installation location and method of transducers with different frequencies, and their performance characteristics should be matched with the scene. The advantage of low-frequency transducers (20-40kHz) is their strong impact force, making them suitable for handling heavy oil stains and large particle stains. When installing, priority should be given to cleaning the bottom or side of the tank, which allows ultrasonic vibration to directly act on the surface of the workpiece, maximizing the removal of stubborn stains; High frequency transducers (above 100kHz) are designed for precision cleaning and need to be evenly distributed around the tank to ensure that ultrasonic energy covers the entire cleaning area, especially deep into the gaps and micropores of the workpiece, ensuring no dead corners during cleaning and avoiding excessive local energy damage to precision workpieces.

　　第三要點：精準控制工作參數，避免不當操作。不同頻率的換能器，對功率和液位的要求差異很大，不能一概而論。低頻換能器因為要應對重污清洗，可根據污漬厚重程度適當提高功率，但必須注意絕對不能空槽運行，空槽狀態下?lián)Q能器振動無介質緩沖，會瞬間過熱損壞；高頻換能器則相反，功率不宜過高，否則會產生過強的局部能量，劃傷精密工件表面，同時要嚴格保證清洗液位沒過換能器的振子部分，防止振子干燒，這是高頻換能器使用的關鍵禁忌。

　　Third point: Accurately control working parameters to avoid improper operations. The requirements for power and liquid level vary greatly among transducers of different frequencies, and cannot be generalized. Low frequency transducers can be increased in power according to the severity of heavy stains to cope with cleaning. However, it must be noted that they must not operate in an empty slot. In an empty slot state, the vibration of the transducer is not buffered by a medium, which can cause instantaneous overheating and damage; High frequency transducers, on the other hand, should not have too high a power, otherwise they will generate excessive local energy and scratch the surface of precision workpieces. At the same time, it is necessary to strictly ensure that the cleaning liquid level does not exceed the oscillator part of the transducer to prevent dry burning of the oscillator, which is a key taboo for the use of high-frequency transducers.

　　第四要點：做好定期檢查維護，延長使用壽命。換能器的穩定運行離不開日常養護，使用前后都要做好檢查：首先看換能器與槽體的粘接處是否牢固，有沒有脫膠、開裂的情況，一旦出現粘接問題，會影響超聲能量傳遞，降低清洗效果；長期使用后，要定期檢測振子的性能，如果發現清洗效率明顯下降，比如相同工件清洗時間變長仍洗不干凈，就需要及時校準換能器頻率，或者直接更換新的換能器，避免因換能器性能衰減影響生產效率。

　　Fourth point: Carry out regular inspections and maintenance to extend the service life. The stable operation of the transducer cannot be separated from daily maintenance. Before and after use, it is necessary to check whether the bonding between the transducer and the tank body is firm, whether there is delamination or cracking. Once there is a bonding problem, it will affect the transmission of ultrasonic energy and reduce the cleaning effect; After long-term use, it is necessary to regularly test the performance of the oscillator. If the cleaning efficiency is significantly reduced, such as if the same workpiece cannot be cleaned even after a longer cleaning time, it is necessary to calibrate the frequency of the transducer in a timely manner or directly replace it with a new transducer to avoid the impact of transducer performance degradation on production efficiency.

　　給大家提個實用使用建議：日常使用時，最好把“頻率匹配表”貼在清洗機旁，明確不同換能器對應的發生器頻率，避免操作失誤；安裝和調整參數前，先確認本次清洗的工件類型、污漬情況，再對應選擇換能器頻率和安裝方式。比如清洗機械零件的重油污，就用20-40kHz換能器，底部安裝并適當提功率；清洗光學鏡片等精密件，就用100kHz以上換能器，四周均勻安裝并控制低功率。另外，新?lián)Q能器使用前，建議先空載試運行5-10分鐘，檢查運行狀態是否正常。

　　Here is a practical suggestion for everyone: When using it in daily life, it is best to stick the "frequency matching table" next to the cleaning machine, clarify the generator frequencies corresponding to different transducers, and avoid operational errors; Before installing and adjusting parameters, confirm the type of workpiece to be cleaned and the condition of stains, and then select the corresponding transducer frequency and installation method. For example, to clean heavy oil stains on mechanical parts, a 20-40kHz transducer is used, installed at the bottom, and the power is appropriately increased; To clean precision components such as optical lenses, use a transducer with a frequency of 100kHz or higher, evenly install it around and control low power. Additionally, before using the new transducer, it is recommended to conduct a no-load trial run for 5-10 minutes to check if the operating status is normal.

　　總結下來，超聲波清洗機不同頻率清洗換能器的正確使用，核心就是牢牢抓住“頻率匹配+場景適配”，做好頻率對應、安裝適配、參數控制和定期維護這四件事。只要掌握這些要點，就能充分發揮換能器的性能，保證清洗效果，同時延長設備使用壽命。如果大家在使用過程中遇到換能器頻率校準、故障排查等問題，建議及時咨詢清洗機廠家的專業技術人員，避免盲目拆解維修，造成二次損壞。

　　In summary, the correct use of ultrasonic cleaning machines to clean transducers at different frequencies lies in firmly grasping the "frequency matching+scene adaptation", doing a good job in frequency matching, installation adaptation, parameter control, and regular maintenance. As long as these key points are mastered, the performance of the transducer can be fully utilized, the cleaning effect can be ensured, and the service life of the equipment can be extended. If you encounter problems such as frequency calibration and troubleshooting of the transducer during use, it is recommended to consult professional technicians from the cleaning machine manufacturer in a timely manner to avoid blind disassembly and repair, which may cause secondary damage.

　　本文由 超聲波清洗機  友情奉獻.更多有關的知識請點擊  http://m.yuyingwood.com/  真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from an ultrasonic cleaning machine For more related knowledge, please click http://m.yuyingwood.com/Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.